描述
3M Novec 72DA Engineered Fluid Medium-Heavy Degreasing Defluxing Solvent
Type: Azeotropic Blend
Boiling Point: 44°C
KB Value: 58
Surface Tension: 18.0 dynes/cm
Packing: 5 kg / 20 kg drum
3M Novec 72DA Engineered Fluid is a high-solvency azeotropic blend of methyl nonafluorobutyl ether (10%), ethyl nonafluorobutyl ether (20%), trans-1,2-dichloroethylene (68%), and isopropanol (2%). Formulated for medium- to heavy-duty degreasing and defluxing applications, this clear, colorless, nonflammable fluid delivers exceptional cleaning performance in electronics and precision manufacturing. With a Kauri-Butanol (KB) value of 58 — significantly higher than Novec 71DA (KB 33) — Novec 72DA provides enhanced solvency for removal of resin solder flux residues, heavy oils, greases, and waxes from complex assemblies.
Novec 72DA offers a unique combination of properties: low surface tension (18.0 dynes/cm) for excellent wetting and penetration, azeotropic behavior with consistent boiling composition at 44°C, and zero ozone depletion potential with a GWP of 435. The isopropanol component enhances removal of ionic contaminants, while the blend of HFE-7100 and HFE-7200 provides optimized cleaning performance for a wide range of soils. With t-DCE not classified as a Hazardous Air Pollutant (HAP), Novec 72DA offers a favorable regulatory profile compared to traditional chlorinated solvents, making it an ideal replacement for CFCs, HCFCs, HFCs, nPB, and chlorinated solvents in vapor degreasing and immersion cleaning applications.
Genuine 3M Imported Stock and Technical Support
We supply stable spot inventory of genuine 3M Novec 72DA engineered fluid. Official TDS, SDS, and batch COA documents are available for degreasing, defluxing, and precision cleaning applications.
Request Novec 72DA Quotation, TDS, SDS, and Sample
Complete SDS, COA, and technical documentation available
Core Advantages of 3M Novec 72DA Engineered Fluid
- High solvency: KB value 58 — significantly higher than Novec 71DA for medium- to heavy-duty cleaning
- Dual HFE blend — HFE-7100 and HFE-7200 combination for optimized cleaning performance
- Enhanced ionic contaminant removal — IPA component improves flux residue and salt removal
- Zero ozone depletion potential — environmentally sustainable alternative to ODS solvents
- Nonflammable — no flash point, safe for vapor degreasing and immersion cleaning
- Azeotropic behavior — consistent boiling composition for reliable cleaning performance
- Low surface tension: 18.0 dynes/cm — excellent wetting for complex assemblies and tight spaces
- Favorable regulatory profile — t-DCE is not a Hazardous Air Pollutant (HAP)
Main Applications
- Defluxing of electronic assemblies — removal of resin solder flux residues from printed circuit boards
- Medium- to heavy-duty degreasing — cleaning of heavy oils, greases, waxes, and handling oils
- Vapor degreasing — immersion and vapor phase cleaning of metal and plastic components
- Precision cleaning — cleaning of sensitive electronic components and assemblies
- Rinsing and drying agent — spot-free drying of precision components
- Replacement for chlorinated solvents — alternative to CFC-113, HCFC-141b, nPB, and trichloroethylene
Full Technical Parameters
| Property | Typical Value | Test Method |
| Composition | HFE-7100 (10%) + HFE-7200 (20%) + t-DCE (68%) + IPA (2%) | — |
| Appearance | Clear colorless liquid | Visual |
| Boiling Point | 44°C | ASTM D1078 |
| Freeze Point | -38°C | ASTM D97 |
| Liquid Density (25°C) | 1.27 g/ml | ASTM D891 |
| Surface Tension | 18.0 dynes/cm | — |
| Vapor Pressure (25°C) | 360 mmHg | — |
| Viscosity (25°C) | 0.40 cP | — |
| Kauri-Butanol Value | 58 | — |
| Heat of Vaporization | 60 cal/g | — |
| Ozone Depletion Potential | 0.00 | — |
| Global Warming Potential | 435 | — |
| Flash Point | None | — |
| Flammability | Nonflammable | ASTM E681-94 |
Note: All listed figures are typical values and may vary by production batch. Complete independent qualification testing is required before mass production deployment.
Handling and Storage Recommendations
| Storage Rules | Store sealed original containers in a dry, well-ventilated area away from heat sources and direct sunlight. |
| Forbidden Environments | Avoid exposure to open flames, strong oxidizing agents, and reactive metal powders. |
| Operation Protection | Maintain adequate ventilation. Wear nitrile protective gloves and anti-splash safety goggles during handling. |
Official Technical Documentation
| Document Type | Document Introduction | Document Request |
| TDS | 3M Novec 72DA original factory technical data sheet | Request TDS |
| SDS | Safety data sheet covering transport, storage, and handling guidelines | Request SDS |
| COA | Batch-specific certificate of analysis | Request COA |
Frequently Asked Questions
What is 3M Novec 72DA Engineered Fluid?
3M Novec 72DA is a blend of hydrofluoroethers (HFE-7100 and HFE-7200), trans-1,2-dichloroethylene (t-DCE), and isopropanol. It is designed for medium- to heavy-duty degreasing and defluxing applications in electronics and precision cleaning.
What is the KB value of Novec 72DA?
Novec 72DA has a Kauri-Butanol (KB) value of 58, significantly higher than Novec 71DA (KB 33), providing enhanced solvency for removal of resin flux residues, heavy oils, greases, and waxes.
What is the composition of Novec 72DA?
Novec 72DA contains methyl nonafluorobutyl ether (10%), ethyl nonafluorobutyl ether (20%), trans-1,2-dichloroethylene (68%), and isopropanol (2%). The isopropanol component provides enhanced removal of ionic contaminants.
Is Novec 72DA flammable?
No. Novec 72DA is nonflammable with no flash point, providing safe operation in vapor degreasing and immersion cleaning applications.
What is the boiling point of Novec 72DA?
Novec 72DA has a boiling point of 44°C with a freeze point of -38°C, providing a wide liquid range for vapor degreasing and immersion cleaning.
What applications is Novec 72DA suitable for?
Novec 72DA is ideal for cleaning resin solder flux residues, oils, greases, waxes, and heavy soils from electronic assemblies, as well as precision cleaning of metal and plastic components.
Is t-DCE a Hazardous Air Pollutant?
No. trans-1,2-dichloroethylene (t-DCE) is not considered a Hazardous Air Pollutant (HAP), making Novec 72DA less regulated than traditional chlorinated solvents like trichloroethylene or perchloroethylene.
Related 3M Novec Engineered Fluids
Compare 3M Novec engineered fluids for different cleaning and application requirements.
| Product Grade | Type | KB Value | Boiling Point | Core Application |
| Novec 72DA | HFE blend + t-DCE + IPA | 58 | 44°C | Medium-heavy degreasing, defluxing |
| Novec 71DA | HFE-7100 + t-DCE + Ethanol | 33 | 40°C | Defluxing |
| Novec 71DE | HFE-7100 + t-DCE (50/50) | 27 | 41°C | Medium-duty degreasing |
Get 3M Novec 72DA Bulk Pricing and Technical Support
We supply genuine 3M Novec 72DA engineered fluid for medium- to heavy-duty degreasing, defluxing, and precision cleaning applications. Contact us for bulk pricing, sample availability, technical documents, and application support.
Request Novec 72DA Technical Details
Disclaimer: All technical data on this page are for general guidance only and are not product specifications. Buyers must carry out independent trials and verify suitability before bulk ordering. Actual values may vary between production lots.
