描述
532-6314 Green is an ETFE powder topcoat from Chemours‘ Teflon industrial coatings portfolio, genuinely manufactured by Chemours and imported as original product. As an authorized distributor and trader, we supply genuine material with full traceability and direct access to official Chemours technical documentation. For more product options and company information, please visit our website at https://szrqchem.com/.
532-6314 Green is an ETFE (ethylene tetrafluoroethylene) powder topcoat specifically engineered for high build / thick film applications. ETFE is a thermoplastic copolymer of ethylene and tetrafluoroethylene. Although not fully fluorinated, ETFE has excellent chemical resistance and is the toughest of the fluoroplastics. This resin is extremely tough, abrasion resistant, and has excellent chemical resistance. ETFE is also an excellent electrical insulator and has good nonstick and low friction properties.
The 532-631x product line is designed for high-build topcoats, has outstanding resistance to heat, and is specially formulated to resist sagging in thick films. The green pigmented finish provides a distinctive industrial appearance while delivering superior protection against chemical corrosion. The coating sintered film is very dense and nonporous, providing excellent chemical resistance.
532-6314 is FDA compliant for food contact applications per 21CFR when used in combination with a compliant layer and properly cured, making it suitable for food processing equipment, industrial bakeware, and other food‑contact uses. As a powder coating, 532-6314 contains zero VOCs, offering significant environmental and worker safety advantages.
With regular stock availability, we support both trial orders and large‑volume bulk shipments for chemical processing, semiconductor equipment, food processing, pharmaceutical manufacturing, and other demanding industrial applications.
Key Features of 532-6314 Green ETFE Powder Topcoat
-
High Build / Thick Film Capability – Single coat 4.0-6.0 mil (102-152 µm); maximum total film build up to 25.0 mils (approx. 635 µm) . Film thicknesses up to 250 µm per coat are achievable.
-
Sag Resistance – Specially formulated to resist sagging in thick films, ensuring uniform coating even at high film builds.
-
Extremely Tough & Abrasion Resistant – ETFE is the toughest of the fluoroplastics, providing superior mechanical strength and wear resistance.
-
Excellent Chemical Resistance – Sintered coating forms a very dense, nonporous film with outstanding resistance to chemical corrosion.
-
FDA Food Contact Compliant – FDA compliant for food contact applications per 21CFR when used with a compliant layer and properly cured.
-
Green Finish – Distinctive green pigmented finish for easy visual identification and consistent industrial appearance.
-
High Temperature Resistance – Continuous service up to 149°C (300°F) with intermittent service up to 302°C (575°F).
-
Good Nonstick & Low Friction Properties – Provides good nonstick release and low friction characteristics.
-
Excellent Dielectric Strength – ETFE is an excellent electrical insulator, suitable for electrical and semiconductor applications.
-
Zero VOC Formulation – Powder coating contains 0 g/kg VOC, offering significant environmental and worker safety advantages.
-
Broad Substrate Compatibility – Compatible with aluminum, stainless steel, and carbon steel substrates.
-
System Compatibility – Interchangeable and compatible with liquid and powder topcoats for multi‑coat systems.
Typical Applications for 532-6314 Green
| Industry | Typical Components & Considerations |
|---|---|
| Chemical Processing | Reaction vessels, agitators, pipelines, pumps, tanks, valves – resists strong acids and alkalis, ensures equipment stability and service life |
| Semiconductor Equipment | High‑purity components, circuit board baking trays – stable at high temperatures, no harmful substance release |
| Food Processing | Bakeware, conveyor belts, cutting tools – FDA compliant, ensures easy release and cleaning |
| Pharmaceutical Manufacturing | Pharmaceutical production equipment – requires high purity and chemical resistance |
| Plastic & Rubber Industry | Rollers, shoe molds, rubber glove molds, tire molds – prevents sticking, extends mold life |
| Textile Industry | Rollers for yarn sizing – prevents high‑viscosity chemical slurry adhesion |
| Medical Devices | Surgical instruments, infusion tubes – reduces friction, improves durability |
| Aerospace | Aircraft engine components, fuel system piping – stable performance in extreme environments |
| Power & Energy | Power generation equipment – chemical resistance and high dielectric strength |
| Valve & Pump Components | Industrial valves, pumps – corrosion protection and thick film durability |
| General Industrial | Components requiring ETFE nonstick properties with high build, green finish |
Material Advantages
532-6314 Green ETFE Powder Topcoat delivers:
-
High Build Capability – Supports total film thickness up to 25.0 mils (approx. 635 µm) , providing enhanced abrasion resistance, corrosion protection, and extended service life. Single coat film build of 4.0-6.0 mil (102-152 µm) enables efficient application.
-
Sag Resistance in Thick Films – Specially formulated to resist sagging, ensuring uniform coating quality even at maximum film builds.
-
Exceptional Toughness – ETFE is the toughest of the fluoroplastics, offering superior impact resistance and mechanical strength compared to PTFE, FEP, or PFA.
-
Excellent Chemical Resistance – Forms a very dense, nonporous film with outstanding resistance to chemical corrosion.
-
Abrasion Resistance – Extremely tough and wear-resistant, extending service life in demanding applications.
-
Food Safety – FDA compliant for food contact per 21CFR when used with a compliant layer, enabling use in food processing and food‑contact applications.
-
Thermal Stability – Maintains performance at continuous service temperatures up to 149°C (300°F), with intermittent service up to 302°C (575°F).
-
High Dielectric Strength – Excellent electrical insulation properties for electrical and semiconductor applications.
-
Zero VOC – Powder formulation contains no VOCs, offering significant environmental and worker safety advantages.
-
Good Nonstick & Low Friction – Provides good release properties and low friction characteristics.
-
Broad Substrate Compatibility – Applicable to aluminum, stainless steel, and carbon steel.
-
System Flexibility – Interchangeable and compatible with liquid and powder topcoats for multi‑coat systems.
Chemours, as the inventor of Teflon, brings over 80 years of fluoro‑polymer expertise, ensuring batch‑to‑batch consistency, reliable supply, and full technical support.
Typical Properties
| Property | 532-6314 Green | Unit / Remarks |
|---|---|---|
| Product Type | ETFE High Build Powder Topcoat / Midcoat | |
| Color | Green | – |
| Form | Powder | Zero VOC |
| Coating System | Topcoat – High Build | Must be used with primer |
| FDA Compliance | Yes – Food Contact per 21CFR | When properly cured |
| CAS Number | 25038-71-5 | |
| Coverage | 22.0 m²/kg (110 ft²/gal) | |
| Average Particle Size | 76 – 96 μm | |
| Bulk Density | 55 – 85 g/100 cc | |
| Density | 1.70 kg/L (14.22 lbs/gal) | |
| Max Continuous Service Temp. | 149°C (300°F) | |
| Intermittent Service Temp. | 302°C (575°F) | |
| Cure Temperature | 270-290°C (520-555°F) | 20-30 minutes |
| Single Coat Film Build | 4.0 – 6.0 mil (102 – 152 µm) | |
| Recommended DFT per Coat | Up to 250 µm (9.8 mil) | |
| Max Total Film Build | 25.0 mil (approx. 635 µm) | High Build |
| Chemical Resistance | Excellent – resists acids, alkalis, solvents | |
| Abrasion Resistance | Excellent – extremely tough | |
| Dielectric Strength | Very good | |
| Application Method | Electrostatic Spray / Fluidized Bed | |
| Recommended Primer | Liquid 699N-129, Powder 532G-6405 | |
| Packaging | 4 kg, 5 kg, 10 kg, 20 kg pails / bags | |
| Shelf Life | 18 months | Unopened, proper storage |
Important Notes on Typical Data:
-
Values listed are typical and sourced from Chemours official data sheets. They do not constitute binding product specification.
-
Physical constants are averages only and may vary up to ±5% of the values shown.
-
Theoretical coverage at dry film thickness of 25 µm (1.0 mil) based on 100% application efficiency. It does not take normal production losses into account.
-
Final performance depends on substrate preparation, application method, and curing conditions.
-
Chemours original TDS shall serve as definitive technical reference. Request the latest official TDS from our sales team.
Processing Guidelines
| Step | Process |
|---|---|
| Substrate | Aluminum, stainless steel, carbon steel |
| Surface Preparation | Remove all grease and contaminants. Use organic solvents to dissolve grease and heat to approximately 400°C to volatilize, then grit blast to roughen the surface |
| Powder Preparation | Homogenize powder before opening bag |
| Screening | 30 mesh (approx. 550 μm) stainless steel or nylon. Insufficient screening can result in application defects |
| Primer Application | Recommended primer: Liquid 699N-129 or Powder 532G-6405. If powder primer is used with a complete powder system, efficiency is higher |
| Application Method | Use fluidized bed with or without vibration system (depends on powder quantity and particle size). On flat and/or conductive parts, high voltage and higher amperage can be used. On insulated and complex parts, amperage should be lowered |
| Recommended General Settings | • Product supply: 30-50% • Air carrier: 3.0 nm³/hr • Fluidization bed: 0.3 nm³/hr • Electrode fluidization: Flat jet 0.2 nm³/hr • Amperage: 10 μA • Voltage: 60 kV |
| Spray Distance | 20-30 cm from substrate |
| Single Coat DFT | 4.0 – 6.0 mil (102 – 152 µm) |
| Recommended DFT per Coat | Up to 250 µm (9.8 mil) |
| Max Total DFT | 25.0 mil (approx. 635 µm) |
| Drying (Metal Temp.) | Powders can be applied dry on wet. Full coating system should be dried before final cure |
| Curing | 20-30 minutes at 270-290°C (520-555°F) . Prolonged exposure at or above the maximum bake temperature can affect performance |
| Storage | Store in original, sealed containers in a cool, dry place away from direct sunlight |
| Shelf Life | 18 months in unopened, clean, dry storage |
Critical Processing Warnings:
-
Primer Required: 532-6314 is a topcoat and must be used with a compatible primer system (e.g., Liquid 699N-129 or Powder 532G-6405). If powder primer is used with a complete powder system, efficiency is higher.
-
Do Not Apply as Single Coat: This topcoat is designed for use with primer systems and should not be applied as a single coat system.
-
Surface Preparation: Proper surface preparation is critical for adhesion. Remove all grease and contaminants from the surface.
-
High Build Application: Specially formulated to resist sagging in thick films. Single coat 4.0-6.0 mil (102-152 µm), max total 25.0 mil (635 µm).
-
Screening: Insufficient screening can result in application defects.
-
Curing: Cure time and temperature depend on part mass and oven characteristics. Always verify with test pieces.
-
Storage: Store in original, sealed containers in a cool, dry place away from direct sunlight.
-
Shelf Life: 18 months in unopened, clean, dry storage.
Related Products
-
Explore Teflon ETFE Coatings – Browse all Teflon ETFE industrial coating options
-
Explore Teflon PTFE Coatings – Browse all Teflon PTFE industrial coating options
-
850G-300 Clear – Teflon PTFE Acid Primer – Acid primer for PTFE, PFA, and FEP topcoat systems
-
About Our Company – Learn more about our supply capabilities and quality assurance
Technical Documents
| Document Type | Description & Source |
|---|---|
| Chemours Official TDS | Complete physical, thermal, and mechanical properties of 532-6314 Green, issued by Chemours original |
| Chemours Official SDS | GHS‑compliant chemical safety documentation, original Chemours document |
| Chemours Distributor Authorization Certificate | Proof of our authorized‑distributor qualification for Chemours Teflon series, available upon request |
| FDA Compliance Declaration | FDA food contact compliance statement per 21CFR |
| COA (Certificate of Analysis) | Batch‑specific quality certification |
| Application & Usage Guide | Detailed application guidance for ETFE high build powder coating systems |
Request any document above by:
-
Email:
ruiqingchem@gmail.com -
Online form: Our contact page
We reply within one working business day. Please clearly state product (532-6314 Green) and document type you require.
FAQ
Q1: What is 532-6314 Green and what is it used for?
A: 532-6314 Green is an ETFE (ethylene tetrafluoroethylene) powder topcoat from the Teflon industrial coatings portfolio. It is specifically designed for high build / thick film applications with single coat 4.0-6.0 mil (102-152 µm) and max total film build up to 25.0 mils (approx. 635 µm) . It is widely used in chemical processing equipment, semiconductor equipment, food processing, pharmaceutical manufacturing, power generation, aerospace, and general industrial applications.
Q2: Is 532-6314 Green FDA compliant?
A: Yes. 532-6314 is FDA compliant for food contact applications per 21CFR when used in combination with a compliant layer and properly cured.
Q3: What makes 532-6314 different from other ETFE powders?
A: 532-6314 is part of the 532-631x product line designed for high-build topcoats. It offers single coat film build of 4.0-6.0 mil (102-152 µm) and max total film build of 25.0 mils (635 µm) , and is specially formulated to resist sagging in thick films.
Q4: What is the difference between 532-6314 and 532-6310?
A: 532-6310 is Clear and functions as a Topcoat, while 532-6314 is Green and can function as a Midcoat. Both share similar high build capabilities, cure temperatures, and film build specifications.
Q5: Is primer required for 532-6314 Green?
A: Yes. 532-6314 is a topcoat/midcoat and must be used with a compatible primer system. Recommended primers: Liquid 699N-129 or Powder 532G-6405. If powder primer is used with a complete powder system, efficiency is higher.
Q6: What is the temperature range of 532-6314 Green?
A: Continuous service up to 149°C (300°F) with intermittent service up to 302°C (575°F).
Q7: What is the recommended film build for 532-6314 Green?
A: Single coat 4.0-6.0 mil (102-152 µm); recommended DFT per coat up to 250 µm (9.8 mil); maximum total film build 25.0 mil (approx. 635 µm) .
Q8: What is the coverage of 532-6314 Green?
A: Coverage is 22.0 m²/kg (110 ft²/gal) .
Q9: What substrates can 532-6314 Green be applied to?
A: It can be applied to aluminum, stainless steel, and carbon steel.
Q10: Is 532-6314 Green PFA or ETFE?
A: 532-6314 is ETFE (ethylene tetrafluoroethylene) , not PFA. ETFE is a thermoplastic copolymer of ethylene and tetrafluoroethylene and is the toughest among fluoroplastics.
Q11: What is the CAS number of 532-6314 Green?
A: The CAS number is 25038-71-5.
Q12: What is the shelf life of 532-6314 Green?
A: The shelf life is 18 months in unopened, proper storage.
Q13: What is the lead time for orders?
A: Regular orders ship within 7‑10 working days after payment confirmation. Large‑volume or urgent orders can be negotiated.
CTA (Call to Action)
Ready to order 532-6314 Green?
To get a precise quotation and professional technical support, please share:
-
Required quantity (kg)
-
Destination port or delivery address
-
Target application (chemical processing, semiconductor, food processing, pharmaceutical, power generation, aerospace, etc.)
-
Required total film thickness (up to 25.0 mils)
-
Primer requirement (Liquid 699N-129 or Powder 532G-6405)
-
Document requirement (TDS, SDS, FDA compliance, COA, etc.)
Sample Policy:
-
Samples are for laboratory validation tests only, not for production use.
-
Buyer bears international sample‑shipping freight.
-
If bulk‑product performance deviates from sample reference, Chemours official TDS serves as the authoritative benchmark.
Take action now:
-
📧 Email Us –
ruiqingchem@gmail.com -
📝 Send Inquiry – Use our quick inquiry form
-
💬 Live Chat – Click the bottom‑right chat widget to speak directly with our team
After‑Sales Support
| Service | Details |
|---|---|
| Quality Inspection Period | All quality‑related claims must be submitted within 7 working‑days after delivery, supported by test data and photographic evidence. |
| Return / Exchange Policy | Confirmed product defects caused by our side trigger replacement or refund. Terms and conditions apply. |
| Logistics Damage | Report shipping damage directly to carrier immediately upon goods receipt. We assist with claim‑document preparation. |
| Technical Support | Remote technical guidance available. On‑site troubleshooting can be arranged upon special request. |
| Export Documentation | We supply commercial invoice, packing list, bill of lading, COA, and additional compliance certificates (e.g., FDA) on request. |
Disclaimer
DISCLAIMER: All technical data is referenced from original Chemours typical values for 532-6314 Green. Our company acts as authorized distributor/trader rather than original manufacturer. Final performance depends on substrate preparation, application method, and curing conditions. Buyers shall independently validate product suitability for individual applications. Our firm bears no liability for coating failure caused by improper application or improper usage. Always reference the latest Chemours official TDS of 532-6314 Green as the definitive specification.
