描述
ULTEM Resin AUT210 is a high flow, transparent, flame retardant amorphous polyetherimide (PEI) resin manufactured by SABIC. As an authorized distributor and trader, we supply genuine SABIC materials with full traceability.
ULTEM AUT210 is a specialty automotive grade specifically engineered for automotive lighting applications where highly metallized, reflective surfaces are required. It is a transparent high flow Polyetherimide with a glass transition temperature (Tg) of 227°C and very low outgassing and plateout.
ULTEM AUT210 sets a benchmark in automotive reflector applications by delivering exceptional thermal stability and superior melt strength, ensuring dimensional precision even under the extreme heat and pressure cycles of headlamps. Its inherent rigidity and resistance to creep allow the resin to maintain complex reflector geometries, sharp angles, and fine surface textures without distortion. Thanks to its naturally low moisture absorption, it provides consistent optical clarity and metallization quality across manufacturing cycles. Moreover, ULTEM AUT210 offers excellent UV resistance and long-term dimensional stability, making it ideally suited for components exposed to intense light sources and environmental stress.
Key attributes include:
-
Haze Onset Temperature of 212°C – Maintains optical clarity and reflective performance at elevated temperatures; higher than AUT200 (204°C) and AUT195 (195°C)
-
High Flow – Excellent flow characteristics (MVR 16 cm³/10min at 360°C/5kg) for thin-wall molding
-
Highest Heat Resistance in AUT Series – Glass transition temperature (Tg) of 227°C
-
Flame Retardant – Inherently flame retardant without additives; UL94 V-0 rated
-
Excellent Metallization Compatibility – Formulated for superior metal adhesion and reflectivity; very low outgassing and plateout minimize contamination of metallization equipment
-
High Stiffness & Strength – Tensile modulus of 3,320 MPa (ISO) / 3,590 MPa (ASTM); tensile yield strength of 103 MPa (ISO) / 105 MPa (ASTM)
-
Excellent Dimensional Stability – Low shrinkage (0.50-0.70%); low creep sensitivity; high dimensional stability supports efficient assembly of electronic components
-
Good Chemical & Hydrolytic Resistance – Retains strength and resists stress cracking when exposed to automotive and aircraft fluids, aliphatic hydrocarbons, alcohols, acids, and weak aqueous solutions
-
Low Smoke & Low Toxicity – Exceptionally difficult to ignite, with a Limiting Oxygen Index (LOI) of 47%; generates extremely low smoke per NBS Smoke Evolution test; products of combustion no more toxic than wood
-
Good Metal Adhesion – Suitable for applications requiring metal bonding and metallized reflective surfaces
-
PFAS-Free – No PFAS intentionally added during manufacturing
-
Electroplatable – Can be electroplated for decorative or functional metal finishes
-
Versatile Processing – Suitable for injection molding; can also be extruded, thermoformed, and blow molded
Typical Applications for ULTEM AUT210
| Industry | Typical Applications |
|---|---|
| Automotive Lighting | Headlamp reflectors, fog lamp reflectors, bezels, lighting housings – highly metallized reflective surfaces |
| Automotive Exteriors | Exterior trim components, decorative parts requiring metallic finishes |
| Automotive Under the Hood | Engine components, connectors, sensors |
| Electrical & Electronics | LED components, reflectors, housings, electronic components |
| Consumer Goods | High-end lighting fixtures, decorative reflectors |
| Eyewear | Eyewear frames – super tough, UV stabilized, lightweight |
| AR/VR Glasses | High strength-to-weight ratio enables thin wall, light weight design |
AUT Series Comparison
| Property | AUT195 | AUT200 | AUT200M | AUT210 |
|---|---|---|---|---|
| Haze Onset Temperature | 195°C | 204°C | 204°C | 212°C |
| Glass Transition (Tg) | 217°C | 217°C | 217°C | 227°C |
| Internal Mold Release | No | No | Yes | No |
| MVR (360°C/5kg) | — | — | — | 16 cm³/10min |
| Tensile Modulus (ISO) | — | 3,200 | 3,300 | 3,320 MPa |
| Tensile Yield Strength (ISO) | — | 105 | 105 | 103 MPa |
| Key Feature | Entry-level haze onset | Higher haze onset + stiffness | Haze onset 204°C + IMR | Highest heat resistance (Tg 227°C) + highest haze onset (212°C) |
Typical Properties
| Property | AUT210 (ISO) | AUT210 (ASTM) | Unit | Test Method |
|---|---|---|---|---|
| Physical | ||||
| Density | 1.29 | 1.29 | g/cm³ | ISO 1183 / ASTM D792 |
| Melt Volume Rate (MVR) – 360°C/5kg | 16 | — | cm³/10min | ISO 1133 |
| Melt Flow Rate (MFR) – 337°C/6.6kg | — | 11 | g/10min | ASTM D1238 |
| Mold Shrinkage, Flow | — | 0.50 – 0.70 | % | SABIC Method |
| Water Absorption (Saturation) | 1.25 | — | % | ISO 62 |
| Moisture Absorption (23°C/50% RH) | 0.70 | — | % | ISO 62 |
| Mechanical | ||||
| Tensile Modulus | 3,320 | 3,590 | MPa | ISO 527 / ASTM D638 |
| Tensile Strength (Yield) | 103 | 105 | MPa | ISO 527 / ASTM D638 |
| Tensile Strength (Break) | 88 | 88 | MPa | ISO 527 / ASTM D638 |
| Elongation at Yield | 7 | 8 | % | ISO 527 / ASTM D638 |
| Elongation at Break | 50 | 75 | % | ISO 527 / ASTM D638 |
| Flexural Modulus | 3,140 | 3,330 | MPa | ISO 178 / ASTM D790 |
| Impact | ||||
| Izod Impact (Notched, 23°C) | 5 | 37 | kJ/m² / J/m | ISO 180/1A / ASTM D256 |
| Izod Impact (Notched, -30°C) | 4 | 38 | kJ/m² / J/m | ISO 180/1A / ASTM D256 |
| Charpy Impact (Notched, 23°C) | 16 | — | kJ/m² | ISO 179/1eA |
| Thermal | ||||
| Glass Transition Temperature (Tg) | 227 | 227 | °C | |
| Haze Onset Temperature | 212 | 212 | °C | SABIC IP Method |
| Heat Deflection Temp. (1.82MPa) | — | 201 | °C | ASTM D648 |
| Vicat Softening Temp. (B50) | — | 212 | °C | ASTM D1525 |
| Ejection Temperature | 207 | — | °C | |
| Flammability | ||||
| UL 94 Flammability | V-0 | V-0 | — | UL 94 |
| Limiting Oxygen Index (LOI) | 47 | 47 | % | ASTM D2863 |
Important Notes on Typical Data:
-
Values listed are typical and sourced from SABIC official data sheets. They do not constitute binding product specification.
-
Batch-to-batch deviations may exist. For critical applications, validate performance with batch-specific COA certificate.
-
Final performance depends on processing conditions, mold design, and part geometry.
-
SABIC official TDS shall serve as definitive technical reference. Request the latest official TDS from our sales team.
Processing Guidelines (Injection Molding)
| Parameter | Recommended Conditions | |
|---|---|---|
| Drying | ||
| Drying Temperature | 150°C | |
| Drying Time | 4 – 6 hours | |
| Maximum Moisture Content | ≤0.02% | |
| Injection Molding | ||
| Melt Temperature | 370 – 410°C | |
| Front Zone 3 Temperature | 360 – 415°C | |
| Middle Zone 2 Temperature | 350 – 405°C | |
| Rear Zone 1 Temperature | 340 – 395°C | |
| Mold Temperature | 140 – 180°C | |
| Minimum Wall Thickness | 1.2 mm |
Critical Processing Warnings:
-
Drying: ULTEM AUT210 is hygroscopic and must be dried to <0.02% moisture before processing. Dry at 150°C for 4-6 hours.
-
High Flow: This grade offers high flow characteristics (MVR 16 cm³/10min) for processing complex, thin-walled automotive lighting components.
-
Melt Temperature: Recommended melt temperature range is 370-410°C. Avoid excessive residence times to prevent thermal degradation.
-
Metallization Considerations: Formulated for very low outgassing and plateout to minimize contamination of metallization equipment and ensure consistent reflective coating quality.
-
Gate Design: Use large gates and runners to minimize flow resistance and reduce molded-in stress.
-
Regrind: Regrind can be used up to 20-25% with virgin material, provided it is clean and properly dried.
Related Products
-
Explore PEI / Polyetherimide – Browse all ULTEM PEI resin options
-
Explore Engineering Plastics – Browse all engineering plastic materials
-
About Our Company – Learn more about our supply capabilities and quality assurance
Technical Documents
| Document Type | Description & Source |
|---|---|
| SABIC Official TDS | Complete physical, thermal, and mechanical properties of ULTEM AUT210 |
| SABIC Official SDS | GHS-compliant chemical safety documentation |
| UL Yellow Card | UL certification |
| COA (Certificate of Analysis) | Batch-specific quality certification |
| Processing Guide | Detailed processing guidelines for ULTEM AUT210 |
Request any document above by:
-
Email:
ruiqingchem@gmail.com -
Online form: Our contact page
We reply within one working business day. Please clearly state product (ULTEM AUT210) and document type you require.
FAQ
Q1: What is ULTEM AUT210 and what is it used for?
A: ULTEM AUT210 is a high flow, transparent polyetherimide (PEI) resin manufactured by SABIC, specifically engineered for automotive lighting applications where highly metallized, reflective surfaces are required. It is widely used in headlamp reflectors, fog lamp reflectors, bezels, lighting housings, and other automotive exterior components.
Q2: What is the haze onset temperature of ULTEM AUT210?
A: The haze onset temperature is 212°C (SABIC IP method), the highest in the AUT series, ensuring optical clarity and reflective performance at elevated temperatures.
Q3: What is the glass transition temperature of ULTEM AUT210?
A: The glass transition temperature (Tg) is 227°C, the highest in the AUT series, providing superior heat resistance.
Q4: What is the difference between ULTEM AUT200 and AUT210?
A: ULTEM AUT210 offers a higher haze onset temperature (212°C vs 204°C) and a higher glass transition temperature (227°C vs 217°C), providing superior heat resistance and optical clarity at elevated temperatures compared to AUT200.
Q5: What is the density of ULTEM AUT210?
A: The density is 1.29 g/cm³.
Q6: Is ULTEM AUT210 flame retardant?
A: Yes. ULTEM AUT210 is inherently flame retardant without additives with UL94 V-0 rating and a Limiting Oxygen Index (LOI) of 47%.
Q7: What is the melt flow rate of ULTEM AUT210?
A: The Melt Flow Rate (MFR) is 11 g/10min at 337°C, 6.6kg; the Melt Volume Rate (MVR) is 16 cm³/10min at 360°C, 5kg.
Q8: What is the tensile strength of ULTEM AUT210?
A: Tensile yield strength is 103 MPa (ISO) / 105 MPa (ASTM); tensile break strength is 88 MPa.
Q9: What is the tensile modulus of ULTEM AUT210?
A: The tensile modulus is 3,320 MPa (ISO) / 3,590 MPa (ASTM).
Q10: What is the shrinkage of ULTEM AUT210?
A: Mold shrinkage (flow) is 0.50-0.70%.
Q11: What processing methods can be used for ULTEM AUT210?
A: ULTEM AUT210 is suitable for injection molding and can also be extruded, thermoformed, and blow molded. It can achieve thin-wall molding down to 1.2 mm.
Q12: Is ULTEM AUT210 available in custom colors?
A: Yes. ULTEM AUT210 is transparent amber and all colors are customizable via SABIC’s ColorXpress service.
Q13: Is ULTEM AUT210 PFAS-free?
A: Yes. ULTEM AUT210 has no PFAS intentionally added during manufacturing and is ECO Conforming.
Q14: What is the Vicat softening temperature of ULTEM AUT210?
A: The Vicat softening temperature (B50) is 212°C.
Q15: What is the heat deflection temperature of ULTEM AUT210?
A: Heat deflection temperature is 201°C at 1.82 MPa.
Q16: What is the recommended drying condition for ULTEM AUT210?
A: Dry at 150°C for 4-6 hours.
Q17: What is the melt temperature for injection molding ULTEM AUT210?
A: Recommended melt temperature is 370-410°C.
Q18: What is the lead time for orders?
A: Regular orders ship within 7-10 working days after payment confirmation. Large-volume or urgent orders can be negotiated separately.
CTA (Call to Action)
Ready to order ULTEM AUT210?
To get a precise quotation and professional technical support, please share:
-
Required quantity (kg)
-
Destination port or delivery address
-
Target application (automotive lighting, reflectors, bezels, etc.)
-
Processing method (injection molding)
-
Color requirement (transparent amber or custom color via ColorXpress)
-
Document requirement (TDS, SDS, UL, COA, etc.)
Sample Policy:
-
Samples are for laboratory validation tests only, not for production use.
-
Buyer bears international sample-shipping freight.
-
If bulk-product performance deviates from sample reference, SABIC official TDS serves as the authoritative benchmark.
Take action now:
-
📧 Email Us –
ruiqingchem@gmail.com -
📝 Send Inquiry – Use our quick inquiry form
-
💬 Live Chat – Click the bottom-right chat widget to speak directly with our team
After-Sales Support
| Service | Details |
|---|---|
| Quality Inspection Period | All quality-related claims must be submitted within 7 working-days after delivery, supported by test data and photographic evidence. |
| Return / Exchange Policy | Confirmed product defects caused by our side trigger replacement or refund. Terms and conditions apply. |
| Logistics Damage | Report shipping damage directly to carrier immediately upon goods receipt. We assist with claim-document preparation. |
| Technical Support | Remote technical guidance available. On-site troubleshooting can be arranged upon special request. |
| Export Documentation | We supply commercial invoice, packing list, bill of lading, COA, and additional compliance certificates (e.g., UL, RoHS) on request. |
Disclaimer
DISCLAIMER: All technical data is referenced from original SABIC typical values for ULTEM AUT210. Our company acts as authorized distributor/trader rather than original manufacturer. Final performance depends on processing conditions, mold design, and part geometry. Buyers shall independently validate product suitability for individual applications. Our firm bears no liability for product failure caused by improper processing or improper usage. Always reference the latest SABIC official TDS of ULTEM AUT210 as the definitive specification.
